Creality3D® Official Store! EU/US/AU/UK/CA 3D Printer In stock! | Countries ships from China: Malaysia, Mexico, New Zealand, Philippines, Korea etc

Tabla silenciosa mejorada con controlador TMC2208 para Ender 5 PLUS

  • En oferta
  • $ 55.00 USD
  • Precio habitual

Product Description

Tablero silencioso con controlador TMC2208 paraEnder 5 Plus

Esta opción es la actualizada separada para Ender 5 Plus, simplemente enchufe y podría comenzar a imprimir.
AVISO: Esta nueva placa base silenciosa mejorada actualmente no viene previamente preinstalada en Ender 5 Plus. Diferente de la placa regular V2.2, en la posición del chip de conductor de motor paso a paso, el valor de resistencia es diferente (se puede observar directamente en la placa base).

- Conductor de motor paso a paso basado en TMC2208
- Voltaje: Funciona en 12V y 24V.


✔Reducción súper silenciosa y de ruido: use los controladores de motor paso a paso TMC2208, que el componente de la llave para eliminar el motor de la impresora al imprimir.
Bootloader preinstalado: El firmware puede ser modificado por Arduino o Cura con el cable USB.
Preocupación por la seguridad: la protección de la fugitiva térmica está habilitada, si la temperatura se eleva fuera de control, la impresora dejará de calentar y detenerse automáticamente.

Fácil de operar: soporta BL Touch, pero es necesario que Flash sea el firmware primero. Si necesita firmware o tiene algún problema, no dude en ponerse en contacto con nosotros, ofreceremos un soporte técnico profesional para usted.

Ender 5 plus mainboardEnder 5 Plus Sbient PlaageEnder 5 Plus Sbient Plaage


Customer Reviews

Based on 8 reviews
Ender 5 Plus Board nach über 5 Monaten keine Ware !

Ständige Emails wo man vertröstet wird !!
Einfach nur enttäuschend nieeee wieder 50 Euro das Fenster raus geschmissen.

Dale Johnson
Works well on a CR-10 S4

Bought this to replace the stock board on a CR-10 S4. The board is an exact physical match to the stock CR-10 S4 board and installed without any issues. I flashed the board with TH3D's unified software for a CR-10 S4 with the silent board option uncommented. The board works great and now the stepper motors are quiet as church mice. Well worth the price.

Definetly worth it!

Today i've changed my OEM board with the silent board and... wow! This is silence!
The noisiest part is now the powersupply fan, so that'll be my next target!

A must have if you print often.

If you are new to 3D printing, then like me you might think that the noise from your 3D printer is not that bad, and even a little pleasant. Trust me, that will change. Just like the movie Frozen's "Let it Go" was a pretty song the first few times you heard it, after about two dozen times of hearing it, the pleasantness starts to wear off. After about 50 times of hearing it, you want to smash the DVD into pieces. That was my experience with the sounds coming from my Ender 5 Plus.

This silent board put an end to all those sounds. It was extremely easy to install. I started with switching the power wires first, one by one. Then I took the cables and switched them over one by one. The whole process took about 30-45 min. Now the only sound coming from my printer is the fan noise from my power supply.

I print often, so this was money well spent and I would highly recommend it to anyone buying a compatible printer.

Al Chan
The 2.2 Silent Board works great

It's an easy upgrade to the 2.2 Silent. The printer is quiet now with the sound only coming from the power supply fans (which are still too loud). However, you don't get the annoying sounds from the motor drivers. It's an upgrade but in reality for 2020, it should be standard on the 5 Plus because all other printers ship with quiet drivers. If this was 2012, that's a different story and it would have been acceptable.

To do the swap over, takes about 45 minutes. The main issue is that Creality hot glues the connectors and it takes time to remove the hot glue. Additional heat sinks would also be nice to keep the new board running cooler.